D-MAX DSC-737SE Bedienungsanleitung

User Manual HIGH SPEED DOME CAMERA 650 TVL DSC-737SE

10 3) How to connect equipments Connect the image line of a monitor User can control maximum up to 255 cameras

11 Alarm output is tangency output of relay non-load, it can be used up to AC220/10A by connecting the load.

124) HOW TO SET PROTOCOL ① Please the power off ② Switch protocol that user wants to change on as above the cable ③ The p

135) SETTING ADDRESS OF DIP SWITCHES. RX NO DIP SWITCH (HEX) RX NODIP SWITCH (HEX) 1 2 3 4 5 6 7 1 2 3 4 5 6 7 1 ON OFF OFF OFF

14 ● OSD (ON SCREEN DISPLAY) menu control It is the function to call up the Menu ＊User can not only set Preset, Group, Tour, Swing, Trace functions

151. ID SET. This function is to set camera ID up to 16 letters on the monitor. User can choose letters that they want, if user control a jo

165. SHUTTER SPEED As a setting shutter speed mode, it can be distinguished a fast moving subject easily by means of shutter speed up. ※ Attention

179. Slow AE When the scene brightness is changed, camera exposure is adjusted to new condition. Normally the AE is set to work at fast speed but in

18▶ HSBLC MODE - HSBLE LEVEL: Adjust the HLC Sensitivity by selecting Low, Medium or High - MASK STATE: when user select “On” mode, mask areas

19

2

20- IR Correction You can enable or disable the IR (Infra-Red) correction to support IR light or not. Zoom and focus trace data will be switched acc

21 . ③ Preset Swing SET : Set Preset Swing Move next SWING page for the setting, if user presses F/F key in the s

22 ④ GROUP SET: User can set maximum 12 groups. Select a channel then move to next page after pressing F/F key

23 20. TRACE SET PAGE Set TRACE. User can regenerate and save a change of the unrestricted location of ZOOM In/Out and a position of th

24- Resume Time Set : It can select the delay time that the camera move to the place alarming to observe where wrong signal is sensed. User ca

25 - Press F/F button to enter SET mode. - Fix the black square on the middle of area that you want to hide by a joystick, then go b

2626. MANUAL P/T SPEED User can control the maximum speed in controlling of up and down. It can be set Low, Medium, Max and one turn (360°/sec) is

2729. USE PASSWORD - input the password - available set On/Off mode; off mode is factory set - press the F/F button as On mode - A window will

28 1. Preset setting You can set Preset point up to 250. Preset Input.① Preset setting can be set 1 to 250 sequentially after moves the

29 ② Operation of Swing ③ End of Swing (Run Pan) (Run Tilt) 3. Group setting ① Start Group setting mode -

3 Ⅰ CAUTION --------- 4 Ⅱ INTRODUCTION OF PRODUCTS --------- 6 Ⅲ DIRECTIONS FOR USE

30 Repeat input in continual input EX). Register Group No. 1, 3, 6 as Tour ② Start / End Tour

31 1. PRESET MESSAGE CAM-001 GP:01 P002,T001,S64 CAM-001 Save Group 01CAM-001 (GROUP:01) PRESET:001 As

32 CAM-001 SET TOUR GP:01 CAM-001 TOUR&GP:01 PRESET:001CAM-001 CLEAR TOUR & GRPCAM-001 RUN SPI

33 1. You must turn off the power switch before installation of this equipment 2. Avoid installation places where it is the ultimate cold, hot, and

34When it occurred alarm state, it is not exactly presser position or different. Did you set the preset in the set mode? Check setting status of the

35 Ⅶ. DIMENSIONS Wall mount bracket Indoor Type Outdoor Type

36 Ceiling mount bracket In-ceiling mount bracket Indoor Type Outdoor Type

37 Ⅷ. ASSEMBLY DSC-30EWP Wall mount bracket ① Remove t

388 7 9 6 1 2 5 4 3 Assembly of outdoor dome with pole mount pendant DSC-20ECP Wall mount bracket Remove the M

39 Main & Sub Keyboard configuration

4 Thank you for purchasing our product. Please operate the product after being fully aware of the manual. Pease contact us if you have any queries

40 MODEL 28X Zoom □ 37X Zoom □ Image sensor 1/4” Sony double scan CCD∥ Total / Effective pixels NTSC: 520K / 480K PAL: 610K / 570K Horizonta

1

2

3

4 DISTRIBUTED BY

5Caution in Use Do not disassemble the unit and put alien substances in the unit. - Disassembling the unit or putting alien substances such as a m

6 1. DESCRIPTION AND FEATURES Description This camera has been designed elegantly for buildings, department stores that need to be in harmony w

72. INSTALLATION AND CONNECTION 1) Name and function of each part (UPPER COVER) The camera’s body goes to her

82) Installation SEPARATION OF LOWER COVER (Indoor type) Loosen the bolt of the back of lower cover by a sc

9 Open the connector cover, then connect power, data, video cable and sensor The cover is opened if user loo